HPE ProLiant e910 User And Maintenance Manual Download Page 172

Page: 172 / 182

Prerequisites
Before you perform this procedure make sure that you have a small flat-bladed, nonconductive tool available.

Procedure

1. Power down the server blade.

2. Remove the server blade from the chassis.

3. For 2U server blade, remove the top cover.

4. Remove all the options installed on the system board.

5. Remove the system board.

6. Locate the battery on the system board.

7. Use a small flat-bladed, nonconductive tool to carefully lift the battery from the socket.

8. Remove the battery.

To replace the component, reverse the removal procedure.

172 Removal and replacement procedures

Summary of Contents for ProLiant e910























































































































































































Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands

HPE ProLiant e910, User And Maintenance Manual

Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands