HPE ProLiant e910 User And Maintenance Manual Download Page 24

Page: 24 / 182

Hardware options installation

This chapter provides detailed instructions on how to install hardware options.

For more information on supported options, see the product QuickSpecs on the website at:

http://www.hpe.com/info/qs

To view the warranty for your server and supported options, see

Warranty information on page 179.

PCIe riser option

The 1U and 2U HPE ProLiant e910 Server Blades support the following PCIe riser cards:

• HPE ProLiant e910 1U x16 half height, half length left riser card

• HPE ProLiant e910 2U x8 half height, half length right riser card

• HPE ProLiant e910 2U x8 full height, full length left riser card

• HPE ProLiant e910 2U x16 full height, full length left riser card

Installing the PCIe riser option

Prerequisites

Before you perform this procedure, make sure that you have a T-10 Torx screwdriver available.

Procedure

1. Power down the server blade.

2. Remove the server blade from the chassis.

3. For 2U server blade, remove the top cover.

4. For 1U server blade, do the following:

a. Align the slot on the PCIe riser with the alignment post on the server blade.

b. Secure the riser with screws.

24 Hardware options installation

Summary of Contents for ProLiant e910























































































































































































Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands

HPE ProLiant e910, User And Maintenance Manual

Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands