HPE ProLiant e910 User And Maintenance Manual Download Page 159

Page: 159 / 182

To replace the component, reverse the removal procedure.

Removing and replacing the GPU power enablement board

The GPU power enablement board is installed for 2U e910 server blade only.

Prerequisites

Before you perform this procedure, make sure that you have a T-10 Torx screwdriver available.

Procedure

1. Power down the server blade.

2. Remove the server blade from the chassis.

3. For 2U server blade, remove the top cover.

4. Disassemble the top cover.

5. Disconnect the cables connected to the GPU power enablement board.

6. Remove the expansion card installed.

Removal and replacement procedures

159

Summary of Contents for ProLiant e910























































































































































































Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands

HPE ProLiant e910, User And Maintenance Manual

Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands