HPE ProLiant e910 User And Maintenance Manual Download Page 32

Page: 32 / 182

d. If you are installing a second SSD, repeat steps a–c.

For 2U server blade, do the following:

a. Install the air baffle.

b. Install the top cover.

Install the server blade in the chassis.

10. Power up the server blade.

GPU power enablement option

This option is available for the 2U server blade.

Installing the GPU power enablement option

The server blade supports PCI card, PCIe card and GPU. If these expansion cards have additional power requirement, the GPU
power enablement option is installed.

Procedure

Power down the server blade.

Remove the server blade from the chassis.

Remove the top cover.

Disassemble the top cover.

32 Hardware options installation

Summary of Contents for ProLiant e910























































































































































































Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands

HPE ProLiant e910, User And Maintenance Manual

Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands