HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 124

Page: 124 / 126

Index

link status

configuration options 6-12, 6-13

command 4-11

Gigabit Ethernet (gig) configuration 6-12

display setting 4-2

port mirroring, configuration 6-24

duplex mode 4-2, 4 -11

port number 4-11

port speed 4-2, 4-11

linkt (SNMP option) 6-24

port statistics 5-2

LISTENING (port state) 4-13

port trunking configuration 6-26

log, syslog messages 6-7

ports

disable (temporarily)   6-14
information   4-15
IP status   4-4

membership of the VLAN 4-14

Main Menu 2-1

priority 4-13

Maintenance Menu 9-1

STP port priority 6-22

management processor (MP)

priority (STP port option) 6-22

display MAC address 4-2, 4 -9

prisrv, primary radius server 6-9

statistics 5-11

ptcfg (TFTP save command) 6-27

trace buffer 9-4

pushd command 2-4

mask, IP interface subnet address 6-15

pwd command 2-4

media access control (MAC) address

ARP information 4-5

display address 1-3, 4 -9

quiet (screen display option) 2-4

FDB information   4-7
FDB manipulation   9-3
location   4-2

Miscellaneous Debug Menu 9-4

RADIUS Server Menu 6-9

mmask, system option 6-5

read community string (SNMP option) 6-23

mnet, system option 6-5

reboot 9-1, 9 -7

monitor port 6-24

restarting switch setup 3-3

MP packet statistics 5-12

retries, radius server 6-9

MP-specific SFD statistics 5-14

retry, health checks for default gateway 6-16
revert apply command 2-3, 6 -3

revert command 2-3, 6-3

Network Time Protocol (NTP)

synchronization 6-10

time zone 6-10

save command 2-3, 6-3, 8-5

Network Time Protocol (NTP) Server Menu 6-10

save n command 2-3

null modem cable 1-2

secret, radius server 6-9
secsrv, secondary radius server 6-9

Secure Shell (SSH)

online help 2-3

encryption and authentication methods 1-4

operating mode, configuration 6-13

supported clients 1-4

Operations Menu 7-1

Secure Shell Server (SSHD) Menu 6-7
Setup utility

basic system configuration 3-3

bootstrap protocol (BOOTP) 3-5

panic

configuration 6-27

command 9-7

introduction 3-1

switch 9-1

IP configuration 3-8

passwords, defaults 1-5, 3 -11

port auto-negotiation mode 3-6

ping command 2-4

port configuration 3-5

popd command 2-4

restart 3-3

port configuration 6-12

Spanning Tree Protocol 3-5

Port Menu

start 3-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

Index-3

COMPAQ CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 1:12 PM

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands