HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 33 | Manualshive

Page: 33 / 126

background image

First-Time Configuration

3. From

the

Configuration Menu,

use the following command to select the

System Menu:

>> Configuration#

sys

The

System Menu

is displayed.

[System Menu]
syslog - Syslog Menu
sshd - SSH Server Menu
radius - RADIUS Authentication Menu
ntp - NTP Server Menu
date - Set system date
time - Set system time
idle - Set timeout for idle CLI sessions
snmp - Set SNMP access control
wport - Set Web server port number
notice - Set login notice

bannr - Set login banner
mnet - Set management network
mmask - Set management netmask
tnport - Set Telnet server port number
hprompt - Enable/disable display hostname(sysName)in CLI prompt
bootp - Enable/disable use of BOOTP
http - Enable/disable HTTP (Web) access
user - User Access Control Menu (passwords)
cur - Display current system-wide parameters

4. Enter the following command to set the administrator password:

System#

user/admpw

5. Enter the current administrator password at the prompt:

Changing ADMINISTRATOR password; validation required...

Enter current administrator password:

NOTE:

If you forget your administrator password, call your technical support representative for

help using the password fix-up mode.

6. Enter the new administrator password at the prompt:

Enter new administrator password:

7. Enter the new administrator password, again, at the prompt:

Re-enter new administrator password:

8. Apply and save your change by entering the following commands:

System#

apply

System#

save

3-12

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:50 PM

«
...
31
32
33
34
35
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: Dataprobe Pages: 3

Brand: Panasonic Pages: 206

Brand: Kramer Pages: 8

Aeotec Micro Smart Energy Switch G2

Brand: Aeon Labs Pages: 11

Brand: Witura Pages: 21

Crouse-Hinds CEAG KO

Brand: Cooper Pages: 12

Brand: Linksys Pages: 3

Brand: Intermatic Pages: 1

Brand: QSFPTEK Pages: 12

Brand: Pilz Pages: 8

Brand: Canoga Perkins Pages: 7

Brand: GarrettCom Pages: 77

Brand: Black Box Pages: 20

Nivotester FTC325

Brand: Endress+Hauser Pages: 40

Brand: Dusun Pages: 18

Brand: Enable-IT Pages: 49

Brand: Campbell Pages: 10

Brand: APG Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands