HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 23 | Manualshive

Page: 23 / 126

background image

First-Time Configuration

Starting Setup When You Log In

To start the Setup utility:

1. Connect to the GbE2 Interconnect Switch console. After connecting, the login prompt

displays.

HP ProLiant BL p-Class F-GbE2 Interconnect Switch A
Copyright(C)2003 Hewlett-Packard Development Company, L.P.

Password:

2. Enter

admin

as the default administrator password.

The system displays the

Main Menu

with administrator privileges.

[Main Menu]
info - Information Menu
stats - Statistics Menu
cfg - Configuration Menu

oper - Operations Command Menu
boot - Boot Options Menu
maint - Maintenance Menu
diff - Show pending config changes [global command]
apply - Apply pending config changes [global command]
save - Save updated config to FLASH [global command]
revert - Revert pending or applied changes [global command]
exit - Exit [global command, always available]

>> Main#

3. From

the

Main Menu

, enter the following command to access the

Configuration Menu:

Main#

/cfg

The

Configuration Menu

is displayed.

[Configuration Menu]
sys - System-wide Parameter Menu
port - Port Menu
ip - IP Menu
vlan - VLAN Menu
stp - Spanning Tree Menu
snmp - SNMP Menu
pmirr - Port Mirroring Menu
trunk - Trunk Group Menu
setup - Step by step configuration set up
dump - Dump current configuration to script file

ptcfg - Backup current configuration to tftp server
gtcfg - Restore current configuration from tftp server

3-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:50 PM

«
...
21
22
23
24
25
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: Yeastar Technology Pages: 11

Brand: Communica Pages: 5

Brand: AdLuminis Pages: 8

Brand: ASTEK Pages: 3

Brand: E&C Pages: 10

852-1411/000-001

Brand: WAGO Pages: 40

SI1P-SH-DVI-UCAC

Brand: Black Box Pages: 16

Brand: Network Technologies Pages: 7

Brand: Madison Pages: 2

Brand: H3C Pages: 96

Brand: NVision Pages: 86

Brand: M-E Pages: 36

Brand: Kramer Pages: 46

Brand: Gefen Pages: 12

Wattstopper EOSW Series

Brand: LEGRAND Pages: 12

Brand: Link Pages: 35

AVS-OP-1616-567SD

Brand: AMX Pages: 1

Brand: APG Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands