HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 115

Page: 115 / 126

The Maintenance Menu

The following table describes the

Maintenance Menu

options.

Table 9-1: Maintenance Menu Options

Command Usage

sys

Displays the

System Maintenance Menu

fdb

Displays the

Forwarding Database Manipulation Menu

debug

Displays the

Debug Menu

arp

Displays the

ARP Cache Manipulation Menu

uudmp

Displays dump information in uuencoded format.

ptdmp hostname, filename

[-mgmt|-data]

Saves the system dump information via TFTP.

cldmp

Clears dump information from flash memory.

panic

Dumps MP information to flash and reboots.

tsdmp

Dumps all GbE2 Interconnect Switch information, statistics,
and configuration.

System Maintenance Options

Command:

/maint/sys

[System Maintenance Menu]
flags - Set NVRAM flag word

The

System Maintenance Menu

is reserved for use by HP technical support. The options are

used to perform system debugging.

The following table describes the

System Maintenance Menu

options.

Table 9-2: System Maintenance Menu Options

Command Usage

flags

<new NVRAM flags

word as 0xXXXXXXXX>

This command sets the flags that are used for debugging
purposes by HP technical support.

9-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 1:11 PM

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands