HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 27

Page: 27 / 126

First-Time Configuration

3. Configure Gigabit Ethernet port auto-negotiation mode.

The system prompts:

Port Auto-negotiation:

Current Port 1 auto-negotiation: on

Enter new value ["on"/"off"]:

Enter

off.

Press the

Enter

key to keep the current setting.

4. If configuring VLANs, enable or disable VLAN tagging for the port.

If you selected to configure VLANs in Part 1, the system prompts:

Port VLAN tagging config (tagged port can be a member of multiple
VLANs)

Current TAG flag: disabled

Enter new TAG status [d/e]:

Enter

to disable VLAN tagging for the port or enter

to enable VLAN tagging for the

port. To keep the current setting, press the

Enter

key.

5. The system prompts you to configure the next port:

Enter port number:

When you are finished configuring ports, press the

Enter

key without specifying any

port. Otherwise, repeat the steps in this section.

Setup Part 3: VLANs

If you selected to skip VLAN configuration in Part 1, skip to the “Setup Part 4: Internet
Protocol Configuration” section.

1. Enter the number of the VLAN to configure, or press the

Enter

key to skip VLAN

configuration at the prompt:

VLAN Config:

Enter VLAN number from 2 to 4095, NULL at end:

If you wish to change settings for individual VLANs, enter the number of the VLAN you
wish to configure. “NULL at end” means to skip VLAN configuration, press the

Enter

key without typing a VLAN number. If you skip VLAN configuration, go to the “Setup
Part 4: Internet Protocol Configuration” section.

2. Enter the new VLAN name at the prompt:

Current VLAN name:

Pending new VLAN name: VLAN 2

Enter new VLAN name:

3-6

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:50 PM

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands