HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 51

Page: 51 / 126

The Information Menu

IP Information

Command:

/info/ip

Interface information:
1: 47.80.23.243 255.255.254.0 47.80.23.255, vlan 1, up
Default gateway information:

1: 47.80.22.1, vlan any, up
2: 47.80.225.2, vlan any, up

The following interface and default gateway information is displayed:

Interface number

•
•
•
•
•
•

IP address

IP mask

IP broadcast address

VLAN membership

Operational status

Trunk Group Information

Command:

/info/trunk

Trunk group 1, port state:
1: STG 1 forwarding
2: STG 1 forwarding

When trunk groups are configured, you can view the state of each port in the various trunk
groups.

NOTE:

If Spanning Tree Protocol on any port in the trunk group is set to forwarding, the remaining

ports in the trunk group will also be set to forwarding.

Clear Syslog Messages

Command:

/info/clrlog

This command clears the syslog messages. Refer to the “Show Last 30 Syslog Messages”
section earlier in this chapter for more information.

4-16

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:51 PM

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands