HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 41 | Manualshive

Page: 41 / 126

background image

The Information Menu

Show All ARP Entry Information

Command:

/info/arp/dump

IP address Flags MAC address VLAN Port Referenced SPs
--------------- ----- ----------------- ---- ---- ---------------
47.80.22.1 00:e0:16:7c:28:86 1 6 empty
47.80.23.243 P 00:03:42:fa:3b:30 1 1-4
47.80.23.245 00:c0:4f:60:3e:c1 1 6 empty
190.10.10.1 P 00:03:42:fa:3b:30 10 1-4

The

Referenced SPs

field displays switch ports that request ARP entry. Traffic that comes

into the referenced ports has the destination IP address. From the ARP entry (the referenced
ports), this traffic needs to be forwarded to the egress port (port 6 in the above example).

The

Flag

field provides additional information about an entry. If no flag displays, the entry is

normal.

Table 4-3: ARP Dump Flag Parameters

Flag Description

P

Permanent entry created for GbE2 Interconnect Switch IP interface.

R

Indirect route entry.

U

Unresolved ARP entry. The MAC address has not been learned.

ARP Address List Information

Command:

/info/arp/addr

IP address IP mask MAC address VLAN Flags
--------------- --------------- ----------------- ---- -----

205.178.18.66 255.255.255.255 00:70:cf:03:20:04 P
205.178.50.1 255.255.255.255 00:70:cf:03:20:06 1
205.178.18.64 255.255.255.255 00:70:cf:03:20:05 1

This screen displays all entries in the ARP cache.

4-6

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:51 PM

«
...
39
40
41
42
43
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: IBM Pages: 166

Brand: Lantronix Pages: 2

Brand: Communica Pages: 5

Brand: NETGEAR Pages: 8

Brand: GBC Pages: 2

EXT-UHDA-HBTL-RX

Brand: Gefen Pages: 33

Brand: Sunix Pages: 55

Brand: DX Engineering Pages: 4

Brand: Eaton Pages: 12

Brand: Gefen Pages: 12

Brand: Allen-Bradley Pages: 4

Area box distribution switch

Brand: LEGRAND Pages: 87

Brand: H3C Pages: 4

Brand: CYP Pages: 64

Brand: SolidView Pages: 39

Brand: TESmart Pages: 34

Brand: Accton Technology Pages: 426

Catalyst Express 500 Series

Brand: Cisco Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands