HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 36 | Manualshive

Page: 36 / 126

background image

4

The Information Menu

Introduction

You can view configuration information for the GbE2 Interconnect Switch in the user,
operator, and administrator command modes. This chapter discusses how to use the CLI to
display GbE2 Interconnect Switch information.

Information Menu

Command:

/info

[Information Menu]
arp - ARP Information Menu
fdb - Forwarding Database Information Menu

sys - Show system information
log - Show last 30 syslog messages
link - Show link status
stp - Show STP information
vlan - Show VLAN information
port - Show port information
ip - Show IP information
trunk - Show Trunk Group information
clrlog - Clear syslog messages
dump - Dump all information

The following table describes the

Information Menu

options.

Table 4-1: Information Menu Options

Command Usage

arp

Displays the

Address Resolution Protocol (ARP) Information Menu.

fdb

Displays the

Forwarding Database Information Menu.

continued

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

4-1

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:51 PM

«
...
34
35
36
37
38
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: N-Tron Pages: 20

Brand: Ubisys Pages: 40

Brand: vantiva Pages: 58

Brand: Cardin Elettronica Pages: 2

Brand: SignaMax Pages: 2

Brand: TRENDnet Pages: 16

Brand: Gembird Pages: 2

Brand: Hama Pages: 56

Brand: Wyrestorm Pages: 4

Brand: Cypress Pages: 16

Brand: TRENDnet Pages: 2

Brand: IDT Pages: 158

Brand: H3C Pages: 77

Brand: National Instruments Pages: 12

Brand: Comm-Tec Pages: 10

Brand: MicroNet Pages: 123

Brand: Leaksafe Solutions Pages: 12

Brand: LevelOne Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands