HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 82 | Manualshive

Page: 82 / 126

background image

The Configuration Menu

For instructions on selecting the configuration to run at the next system reset, refer to the
“Selecting a Configuration Block” section in Chapter 8.

System Configuration

Command:

/cfg/sys

[System Menu]
syslog - Syslog Menu

sshd - SSH Server Menu
radius - RADIUS Authentication Menu
ntp - NTP Server Menu
date - Set system date
time - Set system time
idle - Set timeout for idle CLI sessions
snmp - Set SNMP access control
wport - Set Web server port number
notice - Set login notice
bannr - Set login banner
mnet - Set management network
mmask - Set management netmask

tnet - Enable/disable Telnet access
tnport - Set Telnet server port number
hprompt - Enable/disable display hostname (sysName) in CLI prompt
bootp - Enable/disable use of BOOTP
http - Enable/disable HTTP (Web) access
user - User Access Control Menu (passwords)
tport - Set the TFTP port for the system
cur - Display current system-wide parameters

This menu provides configuration of GbE2 Interconnect Switch management parameters such
as user and administrator privilege mode passwords, browser-based management settings,
and management access list.

The following table describes the

System Configuration Menu

options.

Table 6-2: System Configuration Menu Options

Command Usage

syslog

Displays the

Syslog Menu.

sshd

Displays the

SSH Server Menu.

radius

Displays the

RADIUS Authentication Menu.

ntp

Displays the

Network Time Protocol (NTP)

Server Menu.

date

Prompts the user for the system date.

time

Configures the system time using a 24-hour
clock format.

idle

<idle timeout in minutes;

affects both console and Telnet>

Sets the idle timeout for CLI sessions, from 1 to
60 minutes. The default is 5 minutes.

continued

6-4

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:57 PM

«
...
80
81
82
83
84
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: Black Box Pages: 2

SRS Lighting DTS16F-DIN

Brand: plasa Pages: 4

Brand: Zektor Pages: 65

ET2-0602-M Series

Brand: Leonton Pages: 17

Brand: Atlantis Land Pages: 3

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brand: CIS Pages: 3

Brand: TAXON TOOLS Pages: 9

Brand: Abseco Pages: 10

IPES-5222T Series

Brand: Lantech Pages: 30

Brand: Alloy Pages: 33

Brand: NETGEAR Pages: 2

Brand: Lanpro Pages: 16

Brand: J-Tech Digital Pages: 81

Brand: Goobay Pages: 16

Brand: Top View Pages: 13

Brand: Intellinet Pages: 12

AMX Switch Series

Brand: Avocent Pages: 236

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands