HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 63

Page: 63 / 126

The Statistics Menu

Link Statistics

Command:

/stats/port

<port number>

/link

Link statistics for port 1:
linkStateChange: 1

The following table describes the link statistics for a port:

Table 5-6: Link Statistics

Statistics Description

linkStateChange

The total number of link state changes.

Management Processor Statistics

Command:

/stats/mp

[MP-specific Statistics Menu]
pkt - Show Packet stats
tcb - Show All TCP control blocks in use
ucb - Show All UDP control blocks in use
sfd - Show All Socket FD in use
cpu - Show CPU utilization

The following table describes the

MP-specific Statistics Menu

options:

Table 5-7: MP-specific Statistics Menu

Command Usage

pkt

Displays packet statistics, to check for leads and load.

tcb

Displays all Transmission Control Protocol (TCP) control blocks (TCB) that are in
use.

ucb

Displays all User Datagram Protocol (UDP) control blocks (UCB) that are in use.

sfd

Displays all Socket File Descriptors (SFD) that are in use.

cpu

Displays CPU utilization for periods of up to 1, 4, and 64 seconds.

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

5-11

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:53 PM

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands