HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 52

Page: 52 / 126

The Information Menu

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

4-17

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:51 PM

Information Dump

Command:

/info/dump

Use the

dump

command to dump all GbE2 Interconnect Switch information available from

the

Information Menu

(10K or more, depending on your configuration). This data is useful

for tuning and debugging GbE2 Interconnect Switch performance.

If you want to capture dump data to a file, set the communication software on your
workstation to capture session data prior to issuing the dump commands.

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands