HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 59 | Manualshive

Page: 59 / 126

background image

The Statistics Menu

Table 5-4: Ethernet Statistics for Port

continued

Statistics Description

dot3StatsInternalMacTransmitErrors

A count of frames for which transmission on a
particular interface fails due to an internal MAC
sublayer transmit error.

A frame is only counted by an instance of this
object if it is not counted by the corresponding
instance of either the

dot3StatsLateCollisions

object, the

dot3StatsExcessiveCollisions

object, or the

dot3StatsCarrierSenseErrors

object.

The precise meaning of the count represented by
an instance of this object is implementation
specific. In particular, an instance of this object
may represent a count of transmission errors on
a particular interface that are not otherwise
counted.

dot3StatsCarrierSenseErrors

The number of times that the carrier sense
condition was lost or never asserted when
attempting to transmit a frame on a particular
interface.

The count represented by an instance of this
object is incremented at most once per
transmission attempt, even if the carrier sense
condition fluctuates during a transmission
attempt.

dot3StatsFrameTooLongs

A count of frames received on a particular
interface that exceed the maximum permitted
frame size.

The count represented by an instance of this
object is incremented when the

frameTooLong

status is returned by the MAC service to the LLC
(or other MAC user).

Received frames for which multiple error
conditions obtained are, according to the
conventions of IEEE 802.3 Layer Management,
counted exclusively according to the error status
presented to the LLC.

continued

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

5-7

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:53 PM

«
...
57
58
59
60
61
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

SmartCell 6A000

Brand: Cabletron Systems Pages: 114

Brand: Cabletron Systems Pages: 62

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 49

Cabletron CyberSWITCH CSX5500

Brand: Cabletron Systems Pages: 729

Brand: StarTech.com Pages: 24

Brand: B&B Electronics Pages: 22

Brand: Watchguard Pages: 26

Brand: enbrighten Pages: 2

Brand: NETGEAR Pages: 8

Brand: W Box Technologies Pages: 10

Brand: Lantech Pages: 24

Genesis Digital HSM-04-02

Brand: Hall Research Technologies Pages: 28

Brand: Leaksafe Solutions Pages: 12

FiberPlex 1004E

Brand: Patton Pages: 39

Brand: CYP Pages: 24

Brand: Wave Italy Pages: 32

Brand: Hama Pages: 12

Brand: AEB Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands