HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 110 | Manualshive

Page: 110 / 126

background image

The Boot Options Menu

Updating the GbE2 Interconnect Switch Software Image

The GbE2 Interconnect Switch software image is the executable code running on the switch.
A version of the image ships with the GbE2 Interconnect Switch, and comes pre-installed on
the device. As new versions of the image are released, you can upgrade the software running
on your GbE2 Interconnect Switch.

Upgrading the software image on your GbE2 Interconnect Switch requires the following:

•
•
•

•
•
•

Loading the new image onto a TFTP server on your network

Downloading the new image from the TFTP server to your GbE2 Interconnect Switch

Selecting the new software image to be loaded into GbE2 Interconnect Switch memory
the next time the switch is reset

Downloading New Software to Your GbE2 Interconnect Switch

The GbE2 Interconnect Switch can store up to two different software images, called

image1

and

image2,

as well as boot software, called

boot.

When you download new software, you

must specify where it should be placed: either into

image1, image2,

or

boot.

For example, if your active image is currently loaded into

image1,

you would probably load

the new image software into

image2.

This lets you test the new software and reload the

original active image (stored in

image1

), if needed.

To download a new software to your GbE2 Interconnect Switch, you will need the following:

The image or boot software loaded on a TFTP server on your network

The hostname or IP address of the TFTP server

The name of the new software image or boot file

NOTE:

The DNS parameters must be configured if specifying hostnames. Refer to the “Domain Name

System Configuration” section in Chapter 6.

When the above requirements are met, use the following procedure to download the new
software to your GbE2 Interconnect Switch.

1. At

the

Boot Options#

prompt, enter:

Boot Options#

gtimg

2. Enter the name of the GbE2 Interconnect Switch software to be replaced:

Enter name of switch software image to be replaced

["image1"/"image2"/"boot"]:

<image>

3. Enter the hostname or IP address of the TFTP server:

Enter hostname or IP address of TFTP server:

<server name or IP

address>

8-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 1:10 PM

«
...
108
109
110
111
112
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: KE2 Pages: 4

Brand: FAAC Pages: 2

LambdaUnite MSS

Brand: Lucent Technologies Pages: 388

Aeotec Micro Smart Energy Switch G2

Brand: Aeon Labs Pages: 11

Brand: Witura Pages: 21

Brand: GE Pages: 50

Brand: PhD Solutions Pages: 23

Brand: Kramer Pages: 2

Brand: AMAV Pages: 8

Brand: Lantech Pages: 24

Brand: Comet Labs Pages: 46

Hidden Ignition Switch

Brand: Booma-RC Pages: 16

N.JGS516PE-100EUS

Brand: Duxbury Networking Pages: 4

CheetaHub Power-3004E

Brand: Accton Technology Pages: 11

Brand: Kramer Pages: 29

Brand: Niles Pages: 2

Brand: IN-COMMAND Pages: 8

Brand: Myson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands