HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 94 | Manualshive

Page: 94 / 126

background image

The Configuration Menu

Default IP Gateway Configuration

Command:

/cfg/ip/gw

<gateway number>

[Default gateway 1 Menu]
addr - Set IP address
intr - Set interval between ping attempts
retry - Set number of failed attempts to declare gateway DOWN
arp - Enable/disable ARP only health checks
ena - Enable default gateway
dis - Disable default gateway
del - Delete default gateway
cur - Display current default gateway configuration

The GbE2 Interconnect Switch supports two gateways. By default, no gateways are
configured on the switch. Type

1

or

2

in the command as the

<gateway number>

, depending

upon which gateway you want to configure.

The following table describes the

Default IP Gateway Configuration Menu

options.

Table 6-12: Default IP Gateway Configuration Menu Options

Command Description

addr

<default gateway address (such

as, 192.4.17.44)>

Configures the IP address of the default IP
gateway using dotted decimal notation.

intr

<0-60 seconds>

The GbE2 Interconnect Switch pings the default
gateway to verify that it is up. The

intr

option

sets the time between health checks. The range
is from 1 to 120 seconds. The default is 2

seconds.

retry

<number of attempts>

Sets the number of failed health check attempts
required before declaring this default gateway
inoperative. The range is from 1 to 120
attempts. The default is 8 attempts.

arp disable|enable

Enables or disables Address Resolution
Protocol (ARP) health checks. This command is
disabled by default.

ena

Enables the gateway for use.

dis

Disables the gateway.

del

Deletes the gateway from the configuration.

cur

Displays the current gateway settings.

6-16

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:57 PM

«
...
92
93
94
95
96
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

DKVM-16 - KVM Switch

Brand: D-Link Pages: 24

Dis-200G Series

Brand: D-Link Pages: 161

Dis-200G Series

Brand: D-Link Pages: 16

Dis-200G Series

Brand: D-Link Pages: 47

Brand: D-Link Pages: 25

DGS-3100 SERIES

Brand: D-Link Pages: 54

DGS-3100 SERIES

Brand: D-Link Pages: 220

Brand: D-Link Pages: 24

DGS-1248T - Switch

Brand: D-Link Pages: 52

DGS-1216T - Switch

Brand: D-Link Pages: 42

DGS-1216T - Switch

Brand: D-Link Pages: 10

Brand: D-Link Pages: 8

Brand: D-Link Pages: 379

Brand: D-Link Pages: 240

Brand: D-Link Pages: 188

DES-3326S - Switch - Stackable

Brand: D-Link Pages: 349

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands