HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 39

Page: 39 / 126

The Information Menu

Table 4-1: Information Menu Options

continued

Command Usage

vlan

Displays VLAN configuration information, including:

•

VLAN number

•

VLAN name

•

Status

•

Port membership of the VLAN

port

Displays port status information, including:

•

Port number

•

Whether the port uses VLAN tagging or not

•

Port VLAN ID (PVID)

•

Port name

•

VLAN membership

Displays IP Information, including:

•

IP interface information: Interface number, IP address, subnet
mask, broadcast address, VLAN number, and operational status

•

Default gateway information: Interface number, gateway address,
and operational status

trunk

When trunk groups are configured, you can view the state of each
port in the various trunk groups.

clrlog

Clears

syslog

messages displayed with

/info/log.

dump

Dumps all GbE2 Interconnect Switch information available from the

Information Menu

(10K or more, depending on your configuration).

If you want to capture dump data to a file, set your communication
software on your workstation to capture session data prior to issuing
the dump commands.

4-4

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:51 PM

Summary of Contents for ProLiant BL p-Class GbE2































































































































Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands

HP ProLiant BL p-Class GbE2, Command Reference Manual

Search results

Summary of Contents for ProLiant BL p-Class GbE2

Reviews:

Related manuals for ProLiant BL p-Class GbE2

Brands by name

Popular brands