HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 92 | Manualshive

Page: 92 / 126

background image

The Configuration Menu

Temporarily Disabling a Port

To temporarily disable a port without changing its stored configuration attributes, enter the
following command at any prompt:

Main#

/oper/port

<port number>

/dis

Because this configuration sets a temporary state for the port, you do not need to use

apply

or

save.

The port state will revert to its original configuration when the GbE Interconnect

Switch is reset. Refer to the “Operations Menu” section in Chapter 7, for other
operations-level commands.

IP Configuration

Command:

/cfg/ip

[IP Menu]
if - Interface Menu
gw - Default Gateway Menu
dns - Domain Name System Menu
rearp - Set re-ARP period in minutes
cur - Display current IP configuration

The following table describes the

IP Configuration Menu

options.

Table 6-10: IP Configuration Menu Options

Command Description

if

<interface number>

Displays the

IP Interface Menu.

gw

<default gateway number>

Displays the

IP Default Gateway Menu.

dns

Displays the

IP Domain Name System Menu.

rearp

<2-120 minutes>

Sets the re-ARP period in minutes. The GbE2
Interconnect Switch periodically sends ARP (Address
Resolution Protocol) requests to refresh its address
database. This command is used for setting the
interval between ARP refreshes of the next IP
address in the database. The default interval is 10

minutes.

cur

Displays the current IP configuration.

6-14

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:57 PM

«
...
90
91
92
93
94
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Brand: Delta Pages: 4

Brand: DAB Pages: 56

Brand: Ask Pages: 4

Brand: Wavetronix Pages: 3

Brand: Zektor Pages: 13

exta WZM-01 Series

Brand: Zamel Pages: 2

Brand: Omega Pages: 8

Brand: Abseco Pages: 10

Brand: SLV Pages: 22

AVS-OP-2416-340

Brand: AMX Pages: 1

BZ-UHD-88M100-ARC

Brand: BZB Gear Pages: 42

Brand: N-audio Pages: 8

Brand: Gefen Pages: 20

Brand: Broadcast Tools Pages: 10

Brand: PureLink Pages: 12

TriSync COOPER POWER MN230011EN

Brand: Eaton Pages: 12

PDU-ATS-100A-208Y.120-3PH

Brand: Larson Electronics Pages: 14

CrossPoint 450 Plus 3248 HV

Brand: Extron electronics Pages: 186

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands