HP ProLiant BL p-Class GbE2 Command Reference Manual Download Page 66 | Manualshive

Page: 66 / 126

background image

The Statistics Menu

MP-specific SFD Statistics

Command:

/stats/mp/sfd

All Socket FD allocated:
max_fdi=2
fdi=0 fd=15 pfdi=-1
10c27fd8: 0.0.0.0 0<=>47.133.108.161 80 listen TCP server
fdi=1 fd=16 pfdi=-1
10b9564c: 0.0.0.0 0<=>47.133.108.161 23 listen TCP server
fdi=2 fd=17 pfdi=1
10c27c78: 47.129.153.150 5341<=>47.133.108.161 23 accept TCP server

The Socket File Descriptors (SFD) statistics show information about the current management
connections to the GbE2 Interconnect Switch. Each file descriptor index (fdi) lists the IP
address and port number of the connecting party (if applicable), and the service port (http or
Telnet) to which the connection is made. An index line that shows "listen" is waiting for a
connection.

CPU Statistics

Command:

/stats/mp/cpu

CPU utilization:
cpuUtil1Second: 53%
cpuUtil4Seconds: 54%
cpuUtil64Seconds: 54%

The following table describes the management port CPU utilization statistics:

Table 5-11: CPU Statistics

Statistics Description

cpuUtil1Second

The utilization of MP CPU over 1 second. This is shown as
a percentage.

cpuUtil4Seconds

The utilization of MP CPU over 4 seconds. This is shown
as a percentage.

cpuUtil64Seconds

The utilization of MP CPU over 64 seconds. This is shown
as a percentage.

5-14

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:53 PM

«
...
64
65
66
67
68
...
»

Summary of Contents for ProLiant BL p-Class GbE2































































































































Reviews:

No comments

Related manuals for ProLiant BL p-Class GbE2

Infinity IES-1881

Brand: LevelOne Pages: 2

Brand: Comtrend Corporation Pages: 2

Brand: TAXON TOOLS Pages: 9

Brand: Jerguson Pages: 16

Brand: Videplus Pages: 13

Brand: Hama Pages: 14

Brand: Black Box Pages: 31

Brand: Linkskey Pages: 2

Brand: G&D Pages: 80

LMX-2602G-SFP Series

Brand: ANTAIRA Pages: 19

Brand: DANLERS Pages: 2

CT-HDVD-4X14K-SW

Brand: NB Pages: 23

Summit X450-G2-24t-GE4

Brand: Extreme Networks Pages: 2

Brand: ATEN Pages: 15

Brand: Tripp Lite Pages: 9

CONNECTION PERFECTION 32797

Brand: Lindy Pages: 10

Brand: SMC Networks Pages: 3

SRW224P - 10/100 - Gigabit Switch

Brand: Linksys Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands