manualshive.com logo in svg

HP HP-UX SNAplus2, Administration Manual, Page: 96 / 398

Share
Download
HP HP-UX SNAplus2 Administration Manual Download Page 96

96

Chapter 2

Introduction to SNAplus2

SNAplus2 Resources

Default LUs.

If you are configuring type 6.2 dependent LUs for use

with APPC or CPI-C applications, you may wish to define them as
members of the default pool. The default pool can include LUs from more
than one node. An application that does not specify a particular local LU
is assigned an unused LU from the pool of default LUs.

An application requesting a default LU can be assigned to any of these
LUs as available; the LU does not need to be on the same computer as
the application. However, if you are defining partner LUs for the
applications, the partner LUs must be defined on all nodes where default
LUs are defined, so that the application can contact the correct partner
LU using any of the default local LUs defined on any node.

Modes and Classes of Service

A mode specifies a set of characteristics that a type 6.2 local LU uses to
communicate with its partner LU. These characteristics include
information about the way data is transmitted between the two LUs
(such as maximum RU size and pacing window sizes), and about whether
the LUs can establish parallel sessions.

The definition of a mode can also include the name of a class of service
(COS), which specifies minimum and maximum acceptable values for
characteristics such as transmission time, transmission cost, and
network security, together with weightings associated with different
ranges of these values. This enables the node to calculate the best route
across the network when two or more routes to the same remote LU are
available. The configuration of the SNAplus2 node specifies whether the
node performs explicit mapping between modes and COSs. If explicit
mapping is not supported, you do not need to associate a COS with the
mode; the COS name is determined dynamically.

Directory Information

APPN network and end nodes maintain dynamic directory information
about remote nodes and partner LUs. In addition, you can configure such
information directly. On a LEN node, you must configure directory
entries for each partner LU. You can also configure such resources
directly on an APPN end node or network node (for example, to eliminate
the need for a network node to locate a frequently used resource).

Summary of Contents for HP-UX SNAplus2















































































































































































































































































































































































































Reviews:

No comments