HP HP-UX SNAplus2 Administration Manual Download Page 161 | Manualshive

Page: 161 / 398

background image

Chapter 5

161

Defining Connectivity Components

Defining Link Stations

Parameters for Independent LU Traffic

You need the following information to configure this link station for use
by independent LUs (LUs of type 6.2 for use by APPC, 5250, or CPI-C
applications):

Remote node name

The fully qualified CP name of the remote node.
If the remote system is a VTAM host, you can find the
network name (the first eight characters of the fully
qualified name) in the NETID parameter of the VTAM

Start

command. The last eight characters are in the

SSCPNAME parameter of the VTAM

Start

command.
If you enter the name of a new remote node, you can
add a definition for the remote node to enable you to
define partner LUs on the new remote node.
To define a new remote node in this way, specify the
remote node type for this definition rather than
specifying a remote node type of

Discover

. (If the local

node is a LEN node, you do not need to specify the
remote node type, and the Remote node type field does
not apply.) If the local node is an end node rather than
a LEN node, and if you specify a remote node type of
Discover, you do not have to supply the remote node
name. If you do not supply a remote node name, any
adjacent node can use the link station.
Alternatively, you can specify

Discover

dynamically

. This leaves the remote node name

empty and sets the remote node type to

Discover

, so

that any adjacent node can use the link station. The

Discover dynamically

option is not available if the

local node is a LEN node.

Remote node type

The level of APPN support on the remote node that is
accessed through this link station (only applicable if
the local node is an end node).
If you do not know whether the remote node is a LEN
node or end node or whether it is a network node, you
can choose

Discover

. Discovering the level of APPN

support on the remote node can delay link activation

«
...
159
160
161
162
163
...
»

Summary of Contents for HP-UX SNAplus2















































































































































































































































































































































































































Reviews:

No comments

Related manuals for HP-UX SNAplus2

Brand: T&D Pages: 122

Brand: X-Micro Pages: 74

Brand: LORD Pages: 9

Brand: Clavister Pages: 89

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

PCH1 T P Series

Brand: Parker Pages: 107

Brand: Grundig Pages: 24

Brand: eWON Pages: 34

Brand: ZyXEL Communications Pages: 170

Brand: LanReady Pages: 40

Brand: Tripp Lite Pages: 2

Brand: H3C Pages: 148

Brand: QNAP Pages: 11

Brand: Kraun Pages: 16

HDMI Input Card DMC-HD

Brand: Crestron Pages: 1

Brand: CYP Pages: 28

Brand: Asus Pages: 76

Brand: Advantech B+B SmartWorx Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands