HP Compaq 6005 Pro MT Maintenance & Service Manual Download Page 200

Page: 200 / 259

Control panel message

Description

Recommended action

301-Keyboard Error

Keyboard failure.

Reconnect keyboard with computer
turned off.

Check connector for bent or missing
pins.

Ensure that none of the keys are
depressed.

Replace keyboard.

303-Keyboard Controller Error

I/O board keyboard controller.

Reconnect keyboard with computer
turned off.

Replace the system board.

304-Keyboard or System Unit Error

Keyboard failure.

Reconnect the keyboard with computer
turned off.

Ensure that none of the keys are
depressed.

Replace the keyboard.

Replace the system board.

501-Display Adapter Failure

Graphics display controller.

Reseat the graphics card (if applicable).

Clear CMOS. (See Appendix B,

Password Security and Resetting
CMOS on page 235

Verify monitor is attached and turned
on.

Replace the graphics card (if possible).

510-Flash Screen Image Corrupted

Flash Screen image has errors.

Reflash the system ROM with the latest BIOS
image.

511-CPU Fan not detected

CPU fan is not connected or may have
malfunctioned.

Reseat CPU fan.

Reseat fan cable.

Replace CPU fan.

512-Rear Chassis Fan not detected

Rear chassis fan is not connected or may
have malfunctioned.

Reseat rear chassis fan.

Reseat fan cable.

Replace rear chassis fan.

513-Front Chassis Fan not detected

Front chassis fan is not connected or may
have malfunctioned.

Reseat front chassis fan.

Reseat fan cable.

Replace front chassis fan.

515-Power Supply Fan not detected

Power supply fan is not connected or may
have malfunctioned.

Reseat power supply fan.

Reseat fan cable.

Replace power supply fan.

Table C-1

Numeric Codes and Text Messages (continued)

188 Appendix C POST Error Messages

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Search results

Summary of Contents for Compaq 6005 Pro MT

Reviews:

Related manuals for Compaq 6005 Pro MT

Brands by name

Popular brands

HP Compaq 6005 Pro MT, Maintenance & Service Manual

Search results

Summary of Contents for Compaq 6005 Pro MT

Reviews:

Related manuals for Compaq 6005 Pro MT

Brands by name

Popular brands