HP Compaq 6005 Pro MT Maintenance & Service Manual Download Page 158 | Manualshive

Page: 158 / 259

background image

3.

Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive toward
the front of the computer until it locks into place.

Figure 9-30

Installing a Drive into the 3.5-inch Drive Bay (Media Card Reader Shown)

4.

Connect the appropriate drive cables:

a.

If installing a second hard drive, connect the power and data cables to the rear of the drive
and connect the other end of the data cable to the next available (unpopulated) SATA
connector on the system board by following the numbered sequence of the connectors.

b.

If installing a media card reader, connect the USB cable from the media card reader to the
USB connector on the system board labeled MEDIA. If the media card reader includes a 1394
port, connect the 1394 cable to the 1394 PCI card.

NOTE:

Refer to

System Board Drive Connectionson page 138

for an illustration of the

system board drive connectors.

5.

Replace the 5.25-inch drive.

6.

Replace the front bezel and access panel.

146 Chapter 9 Removal and Replacement Procedures Small Form Factor (SFF) Chassis

«
...
156
157
158
159
160
...
»

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Reviews:

No comments

Related manuals for Compaq 6005 Pro MT

Veriton Hornet N260G

Brand: Acer Pages: 22

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 8

Brand: IBM Pages: 393

Brand: Energy Star Pages: 17

Brand: IBM Pages: 165

Brand: U-Line Pages: 6

Brand: PowerCenter Pages: 29

Brand: Diamond Systems Pages: 9

Brand: IconBiT Pages: 31

Brand: Silicon Graphics Pages: 20

Brand: ClearCube Pages: 4

Brand: Rikomagic Pages: 14

Brand: Electronic Pages: 4

Brand: GIGA-BYTE TECHNOLOGY Pages: 2

Brand: Shuttle Pages: 1

ODYSSEY X86J4105

Brand: Seeed Pages: 16

Brand: IEI Technology Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands