manualshive.com logo in svg

HP Compaq 6005 Pro MT, Maintenance & Service Manual

The HP Compaq 6005 Pro MT boasts a powerful and reliable performance, designed to meet your business needs. For hassle-free maintenance and service, you can easily download the comprehensive Maintenance & Service Manual from our website, completely free. Find the manual and enhance your product experience at manualshive.com.

Share
Download
background image

Boot Block Emergency Recovery Mode

Boot Block Emergency Recovery Mode permits system recovery in the unlikely event of a ROM flash
failure. For example, if a power failure were to occur during a BIOS upgrade, the ROM flash would be
incomplete. This would render the system BIOS unusable. The Boot Block is a flash-protected section
of the ROM that contains code that checks for a valid system BIOS image when the system is turned
on.

●

If the system BIOS image is valid, the system starts normally.

●

If the system BIOS image is not valid, a failsafe Boot Block BIOS provides enough support to search
removable media for BIOS image files. If an appropriate BIOS image file is found, it is automatically
flashed into the ROM.

When an invalid system BIOS image is detected, the system power LED will blink red 8 times, one blink
every second. Simultaneously, the speaker will beep 8 times. If the portion of the system ROM containing
the video option ROM image is not corrupt, 

Boot Block Emergency Recovery Mode

 will be displayed

on the screen.

To recover the system after it enters Boot Block Emergency Recovery Mode, complete the following
steps:

1.

Turn off the power.

2.

Insert a CD or USB flash device containing the desired BIOS image file in the root directory.

NOTE:

The media must be formatted using the FAT12, FAT16, or FAT32 file system.

3.

Turn on the computer.

If no appropriate BIOS image is found, you will be prompted to insert media containing a BIOS
image file.

If the system successfully reprograms the ROM, the system will automatically power off.

4.

Remove the removable media used to upgrade the BIOS.

5.

Turn the power on to restart the computer.

NOTE:

BitLocker prevents Windows Vista from booting when a CD containing the BIOS image file is

in an optical drive. If BitLocker is enabled, remove this CD before attempting to boot to Windows Vista.

44

Chapter 5   Desktop Management

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Reviews:

No comments

Related manuals for Compaq 6005 Pro MT

NEC PowerMate eco Getting Started Manual preview
PowerMate eco
Brand: NEC Pages: 28
IBM 5170 Technical Reference preview
5170
Brand: IBM Pages: 462
Yawarra ALIX 3 Outdoor Installation Manual preview
ALIX 3 Outdoor
Brand: Yawarra Pages: 4
IBM 83135CU - NetVista A30 - 8313 Support Manual preview
83135CU - NetVista A30 - 8313
Brand: IBM Pages: 54
PMC MicroMate -101 User Manual preview
MicroMate -101
Brand: PMC Pages: 126
Casio FX-890P Owner'S Manual preview
FX-890P
Brand: Casio Pages: 126
Dell Precision R5400 User Manual preview
Precision R5400
Brand: Dell Pages: 111
IBM 8872 - eServer xSeries 460 Service Manual preview
8872 - eServer xSeries 460
Brand: IBM Pages: 170
Element 14 DIT PI Desktop User Manual preview
DIT PI Desktop
Brand: Element 14 Pages: 17
Moxa Technologies DA-662A Series Quick Installation Manual preview
DA-662A Series
Brand: Moxa Technologies Pages: 2
Paragon F6SR Assembly Instructions preview
F6SR
Brand: Paragon Pages: 2
Gigabyte ST series Quick Start Manual preview
ST series
Brand: Gigabyte Pages: 12
Advantech DS-200 Manual preview
DS-200
Brand: Advantech Pages: 19
E.L.B. FT-30 Technical Documentation Manual preview
FT-30
Brand: E.L.B. Pages: 20
Fujitsu Siemens Computers SCALEO EVi 2555 Datasheet preview
SCALEO EVi 2555
Brand: Fujitsu Siemens Computers Pages: 2
Fujitsu Siemens Computers ESPRIMO P2530 Datasheet preview
ESPRIMO P2530
Brand: Fujitsu Siemens Computers Pages: 4
Daewoo LT7070 User Manual preview
LT7070
Brand: Daewoo Pages: 19
MSI Hetis 800 Series User Manual preview
Hetis 800 Series
Brand: MSI Pages: 80

Brands by name

Popular brands

Load more brands