HP Compaq 6005 Pro MT Maintenance & Service Manual Download Page 147

Page: 147 / 259

Drive Positions

Figure 9-15

Drive Positions

Table 9-3

Drive Positions

3.5-inch internal hard drive bay

3.5-inch external drive bay for optional drives (media card reader shown)

5.25-inch external drive bay for optional drives (optical drive shown)

NOTE:

The drive configuration on your computer may be different than the drive

configuration shown above.

To verify the type, size, and capacity of the storage devices installed in the computer, run Computer
Setup. Refer to the

Computer Setup (F10) Utility Guide

for more information.

Drive Positions 135

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Search results

Summary of Contents for Compaq 6005 Pro MT

Reviews:

Related manuals for Compaq 6005 Pro MT

Brands by name

Popular brands

HP Compaq 6005 Pro MT, Maintenance & Service Manual

Search results

Summary of Contents for Compaq 6005 Pro MT

Reviews:

Related manuals for Compaq 6005 Pro MT

Brands by name

Popular brands