HP Compaq 6005 Pro MT Maintenance & Service Manual Download Page 204

Page: 204 / 259

Control panel message

Description

Recommended action

Network Server Mode Active and No
Keyboard Attached

Keyboard failure while Network Server Mode
enabled.

Reconnect keyboard with computer
turned off.

Check connector for bent or missing
pins.

Ensure that none of the keys are
depressed.

Replace keyboard.

Parity Check 2

Parity RAM failure.

Third-party graphics card may be causing a
problem.

Run Computer Setup and Diagnostic utilities.

Remove third-party graphics card to see if the
problem goes away.

Table C-1

Numeric Codes and Text Messages (continued)

192 Appendix C POST Error Messages

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Search results

Summary of Contents for Compaq 6005 Pro MT

Reviews:

Related manuals for Compaq 6005 Pro MT

Brands by name

Popular brands

HP Compaq 6005 Pro MT, Maintenance & Service Manual

Search results

Summary of Contents for Compaq 6005 Pro MT

Reviews:

Related manuals for Compaq 6005 Pro MT

Brands by name

Popular brands