manualshive.com logo in svg

HP Compaq 6005 Pro MT, Maintenance & Service Manual

The HP Compaq 6005 Pro MT boasts a powerful and reliable performance, designed to meet your business needs. For hassle-free maintenance and service, you can easily download the comprehensive Maintenance & Service Manual from our website, completely free. Find the manual and enhance your product experience at manualshive.com.

Share
Download
background image

Access Panel

1.

Prepare the computer for disassembly (

Preparation for Disassembly on page 74

).

CAUTION:

Before removing the computer access panel, ensure that the computer is turned off

and that the power cord is disconnected from the electrical outlet.

2.

Loosen the two captive thumbscrews 

(1)

 that secure the access panel to the computer chassis.

3.

Use the handle located between the thumbscrews to lift the access panel off the unit 

(2)

.

NOTE:

You may want to lay the computer on its side to install internal parts. Be sure the side

with the access panel is facing up.

Figure 8-2

  Removing the Computer Access Panel

To install the access panel, reverse the removal procedure.

Access Panel

75

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Reviews:

No comments

Related manuals for Compaq 6005 Pro MT

IBM 360 Operating Manual preview
360
Brand: IBM Pages: 48
Radio Shack TRS-80 III Operation Manual preview
TRS-80 III
Brand: Radio Shack Pages: 30
Radio Shack TRS-80 Technical Manual preview
TRS-80
Brand: Radio Shack Pages: 42
Radio Shack TRS-80 Trsdos & Disk Basic Reference Manual preview
TRS-80
Brand: Radio Shack Pages: 192
Radio Shack TRS-80 Reference Manual preview
TRS-80
Brand: Radio Shack Pages: 274
Radio Shack TRS-80 Service Manual preview
TRS-80
Brand: Radio Shack Pages: 44
Radio Shack TRS-80 Preliminary User'S Manual preview
TRS-80
Brand: Radio Shack Pages: 30
IBM NetVista A40 Guía Del Usuario preview
NetVista A40
Brand: IBM Pages: 158
IBM 330 Type 6577 User Manual preview
330 Type 6577
Brand: IBM Pages: 102
Wang Professional Computer Technical Reference Manual preview
Professional Computer
Brand: Wang Pages: 276
EUROCOM LP200ST User Manual preview
LP200ST
Brand: EUROCOM Pages: 113
Advantech MIOS-5250 Startup Manual preview
MIOS-5250
Brand: Advantech Pages: 6
INTERACT AS-1004 Owner'S Manual preview
AS-1004
Brand: INTERACT Pages: 15
Sun Microsystems Sun-1 Reference Manual preview
Sun-1
Brand: Sun Microsystems Pages: 92
E-Medic Silence TP 1 User Manual preview
Silence TP 1
Brand: E-Medic Pages: 31
Gigabyte BRIX GB-BACE-3150 Quick Start Manual preview
BRIX GB-BACE-3150
Brand: Gigabyte Pages: 2
Vivo DESK-V000U Instruction Manual preview
DESK-V000U
Brand: Vivo Pages: 3
Dell Inspiron 5570 Setup And Specifications preview
Inspiron 5570
Brand: Dell Pages: 27

Brands by name

Popular brands

Load more brands