manualshive.com logo in svg

HP Compaq 6005 Pro MT, Maintenance & Service Manual

The HP Compaq 6005 Pro MT boasts a powerful and reliable performance, designed to meet your business needs. For hassle-free maintenance and service, you can easily download the comprehensive Maintenance & Service Manual from our website, completely free. Find the manual and enhance your product experience at manualshive.com.

Share
Download
background image

b.

If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end,
and carefully rock it back and forth until the connectors pull free from the socket. Pull the
expansion card straight up from the socket then away from the inside of the chassis to release
it from the chassis frame. Be sure not to scrape the card against the other components.

NOTE:

Before removing an installed expansion card, disconnect any cables that may be

attached to the expansion card.

Figure 9-10

  Removing a Standard PCI Expansion Card

c.

If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion
socket away from the card and carefully rock the card back and forth until the connectors pull
free from the socket. Pull the expansion card straight up from the socket then away from the
inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against
the other components.

Figure 9-11

  Removing a PCI Express x16 Expansion Card

130 Chapter 9   Removal and Replacement Procedures Small Form Factor (SFF) Chassis

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Reviews:

No comments

Related manuals for Compaq 6005 Pro MT

iDOT V Series User Handbook Manual preview
V Series
Brand: iDOT Pages: 28
Panasonic ToughBook CF-72 Series Supplementary Instructions Manual preview
ToughBook CF-72 Series
Brand: Panasonic Pages: 8
Panasonic Toughbook CF-H2 Operating Instruction preview
Toughbook CF-H2
Brand: Panasonic Pages: 36
Panasonic Toughbook CF-H1CSLFZ6M Reference Manual preview
Toughbook CF-H1CSLFZ6M
Brand: Panasonic Pages: 106
Barco TransForm A User Manual preview
TransForm A
Brand: Barco Pages: 202
Gateway MT-6733 Hardware Replacement Manual preview
MT-6733
Brand: Gateway Pages: 12
MAXDATA Workstation Fusion 7000 User Manual preview
Workstation Fusion 7000
Brand: MAXDATA Pages: 46
Vivo DESK-V000R Instruction Manual preview
DESK-V000R
Brand: Vivo Pages: 3
Omnitronic DMS-1050 Operating Instructions Manual preview
DMS-1050
Brand: Omnitronic Pages: 56
Neousys Technology Nuvo-8108GC Series User Manual preview
Nuvo-8108GC Series
Brand: Neousys Technology Pages: 142
Casio PA-2400U Service Manual And Parts List preview
PA-2400U
Brand: Casio Pages: 81
Asus AS-D250 User Manual preview
AS-D250
Brand: Asus Pages: 52
Asus AAEON BOXER-8251AI User Manual preview
AAEON BOXER-8251AI
Brand: Asus Pages: 39
Asus Aaeon BOXER-8170AI User Manual preview
Aaeon BOXER-8170AI
Brand: Asus Pages: 35
Asus AAEON RTC-1010M User Manual preview
AAEON RTC-1010M
Brand: Asus Pages: 55
Asus AAEON RTC-710RK User Manual preview
AAEON RTC-710RK
Brand: Asus Pages: 43
Asus AS-D850 User Manual preview
AS-D850
Brand: Asus Pages: 38
Asus AAEON BOXER-8240AI User Manual preview
AAEON BOXER-8240AI
Brand: Asus Pages: 53

Brands by name

Popular brands

Load more brands