manualshive.com logo in svg

HP Compaq 6005 Pro MT, Maintenance & Service Manual

The HP Compaq 6005 Pro MT boasts a powerful and reliable performance, designed to meet your business needs. For hassle-free maintenance and service, you can easily download the comprehensive Maintenance & Service Manual from our website, completely free. Find the manual and enhance your product experience at manualshive.com.

Share
Download
background image

Solving USB Flash Drive Problems

If you encounter USB flash drive problems, common causes and solutions are listed in the following
table.

Table D-15

  Solving USB Flash Drive Problems

USB flash drive is not seen as a drive letter in Windows.

Cause

Solution

The drive letter after the last physical drive is not available.

Change the default drive letter for the flash drive in Windows.

USB flash drive not found (identified).

Cause

Solution

The device is attached to a USB port that has been hidden in
Computer Setup.

Run the Computer Setup utility and ensure that “Device
Available” is selected for the USB Ports under 

Security

 >

Device Security

.

The device was not properly seated before power-up.

Ensure the device is fully inserted into the USB port before
applying power to the system

System will not boot from USB flash drive.

Cause

Solution

Boot order is not correct.

Run the Computer Setup utility and change boot sequence
in 

Storage

 > 

Boot Order

.

Removable Media Boot is disabled in the Computer Setup
utility.

Run the Computer Setup utility and enable booting to
removable media in 

Storage

 > 

Storage Options

. Ensure USB

is enabled in 

Storage

 > 

Boot Order

.

The image on the device is not bootable.

Follow the procedures described in the “ROM Flash:
Replicating the Setup: Creating a Bootable Device: Supported
USB Flash Media Device” section of the 

Service Reference

Guide

.

The computer boots to DOS after making a bootable flash drive.

Cause

Solution

Flash drive is bootable.

Install the flash drive only after the operating system boots.

Solving USB Flash Drive Problems 229

Summary of Contents for Compaq 6005 Pro MT




































































































































































































































































Reviews:

No comments

Related manuals for Compaq 6005 Pro MT

Intel Compute Stick STK1A32SC User Manual preview
Compute Stick STK1A32SC
Brand: Intel Pages: 11
Uplift Desk UDA100-clamp Instructions preview
UDA100-clamp
Brand: Uplift Desk Pages: 4
IBM 6868 - IntelliStation M - Pro User Manual preview
6868 - IntelliStation M - Pro
Brand: IBM Pages: 188
Digital Equipment FR-856E*-WB Service Maintenance Manual preview
FR-856E*-WB
Brand: Digital Equipment Pages: 74
AXIOMTEK GOT-5100TL User Manual preview
GOT-5100TL
Brand: AXIOMTEK Pages: 65
Winmate IBDRW100-EX-P User Manual preview
IBDRW100-EX-P
Brand: Winmate Pages: 60
Winmate IH7T-RK2U User Manual preview
IH7T-RK2U
Brand: Winmate Pages: 92
Sony VGN-FW390J Specifications preview
VGN-FW390J
Brand: Sony Pages: 2
Sony VGN-FW378J Specifications preview
VGN-FW378J
Brand: Sony Pages: 2
Sony VGN-FW370J Specifications preview
VGN-FW370J
Brand: Sony Pages: 2
Sony VGN-FW373J Specifications preview
VGN-FW373J
Brand: Sony Pages: 2
Sony VGN-FW351J Specifications preview
VGN-FW351J
Brand: Sony Pages: 2
Sony VGN-FW355J Specifications preview
VGN-FW355J
Brand: Sony Pages: 2
Sony VGN-FW350J Specifications preview
VGN-FW350J
Brand: Sony Pages: 2
Sony VGN-FW340J Specifications preview
VGN-FW340J
Brand: Sony Pages: 2
Sony VGN-FS690 Specifications preview
VGN-FS690
Brand: Sony Pages: 2
Sony VGN-FS680 Specifications preview
VGN-FS680
Brand: Sony Pages: 2
Sony VGN-FS675P Specifications preview
VGN-FS675P
Brand: Sony Pages: 2

Brands by name

Popular brands

Load more brands