8 Channel 2.4 GHz Aircraft Computer Radio System
8 Channel 2.4 GHz Aircraft Computer Radio System
Section 5: Acro and Glider Programming Menu
Section 5: Acro and Glider Programming Menu
72
73
Aileron to Rudder Mixing cont.
19. To set up aileron to rudder mixing in accordance with a Flight
Condition:
- The upper right field of the menu displays which flight
condition is currently active and will be programmed.
- Scroll to the Flight Condition field and press the jog dial to
activate the menu.
- Choose the desired flight condition and press the jog dial to
confirm your selection.
- Repeat steps 4-18 to define the settings for each flight
condition.
If you are using multiple flight conditions, you must define ailevator values for each flight condition.
The top field of the AILEVATOR menu allows you to select the desired flight condition. Alternately,
you may select the desired flight condition using the assigned F.Cond switch.
Note
Tip
Tip
Tip
To disable the aileron-rudder mix:
1. Scroll to highlight the “MIX” field in the aileron-rudder mix
menu and press the jog dial to activate the menu.
2. Select “INH” (inhibit) and press the jog dial to confirm your
selection.
3. Press the back button to return to the model function menu.
20. Press the back button to return to the model function menu.
Elevator to Camber Mixing
The Elevator-to-Camber Mix allows the model to drop and raise the trailing edge of the wing control
surfaces in conjunction with elevator inputs. This function is not valid for the “1AILE” or “ELEVON” wing
types unless flaps are also present. If using a “1AILE + 1FLAP”, “1AILE + 2FLAP”, “ 1FLP”, or
“ 2FLP” wing type, do not configure any settings for the “AILE” function. Configure only flap
servo movements.
To configure an elevator-to-camber mix:
1. From the model menu, rotate the jog dial to highlight
“ELEV>CAMB” and press the jog dial once to enter the activation
menu.
2. Press the jog dial again to activate the menu.
3. Rotate the jog dial to select “ACT” (activate), then press the jog
dial to confirm your selection and activate the elevator-camber
mix menu.
Elevator to Camber Mixing cont.
4. Scroll to the function field (“AILE” or “FLAP”). If “AILE” is not
the current function, press the jog dial to activate the menu.
Otherwise, skip to step 6.
5. Scroll to select “AILE” and press the jog dial to confirm your
selection.
6. Scroll to the top row of the value table (“AILE”) and press the
jog dial to activate the menu.
9. Repeat steps 6-8 to set the endpoints for the servo attached to the “AIL2” receiver slot (second row of
the value table). As with the previous settings, the values input here do not affect the servo travel when
roll commands are given.
10. Scroll to highlight the “EXP” field and press the jog dial to
activate the selection.
11. Rotate the jog dial to input the desired exponential travel of the aileron servos when reacting to this
mix. The setting does not affect exponential travel of the servos when roll commands are given.
12. Scroll to highlight the “OST” (Offset) field and press the jog
dial to activate the menu.
13. Rotate the jog dial to select the desired amount of offset and
press the jog dial to enter your selection.
7. Rotate jog dial to highlight “L/U” (Left/Up) “R/D” (Right/Down)
or both fields. If you want the aileron movement to be the same
for both directions of servo travel, highlight both fields and press
the jog dial.
8. Rotate the jog dial to set the desired endpoints for the servo(s)
attached to the “AILE” receiver slot. This value regards the servo
travel when pitch commands are given. This setting does not
affect the travel of the servo when roll commands are given.
Press the jog dial to confirm your input.
