Hitachi Freedom Storage Lightning 9900 V series Error Code List Download Page 28

Page: 28 / 82

Chapter 1 Error Codes

0305 7205

An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

E 2

0305 7206

An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

E 2

0305 7207

An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

E 2

0305 7208

An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

E 2

0305 7209

An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

E 2

Summary of Contents for Freedom Storage Lightning 9900 V series



















































































Search results

Summary of Contents for Freedom Storage Lightning 9900 V series

Reviews:

Related manuals for Freedom Storage Lightning 9900 V series

Brands by name

Popular brands

Hitachi Freedom Storage Lightning 9900 V series, Error Code List

Search results

Summary of Contents for Freedom Storage Lightning 9900 V series

Reviews:

Related manuals for Freedom Storage Lightning 9900 V series

Brands by name

Popular brands