manualshive.com logo in svg

Hioki RM3542, Instruction Manual, Page: 54 / 218

Share
Download
Hioki RM3542 Instruction Manual Download Page 54

4.5  Improving Probe Contact (Contact Improver Function)

48

For ranges between 1000 k

 and 100 M

, the [PULSE] setting is enabled by default. 

Before measuring in the ranges from 1000 k

 to 100 M

 with the Contact Improver function set to [ON], verify

that measurements are not biased.

1

Open the Basic Settings screen.

2

Open the Measurement Settings Screen.

3

Set the Contact Improver current timing to disabled (OFF), enabled (ON), or PULSE.

(When selecting ON or PULSE)

Set the current limit value.

4

Return to the Measurement screen.

The Basic Settings screen appears.

The Measurement Settings Screen
appears.
[MEAS SETTINGS]

1

Selection

2

Selection

2

Disable probe contact improvement
(go to step 4).

Enable probe contact improvement.

Apply contact improvement current for
about 100 

µ

s immediately before mea-

surement.

1

The setting is specific to the selected range(p. 41)

Selection

1

2

17mA, 25mA, 35mA (default), 50mA

The confirmation screen appears.

Return to the setting screen.

Save setting and return to
previous screen.

Discard setting and return to
previous screen.

Summary of Contents for RM3542



























































































































































































































Reviews:

No comments