manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 94

Cleaning and Disinfecting

80

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Table 1: Approved Cleaners/Disinfectants

*Bleach is not recommended as the primary cleaner/disinfectant. 

Remove any disinfectant residue prior to and after the use of bleach

 with a new or clean 

cloth/wipe soaked in tap water. 

When you perform the detailed cleaning steps, please note the following:

•

A microfiber cloth or the Clorox HealthCare® Bleach Germicidal Wipe is recommended as the 
wiping cloth

.

•

Always replace the wiping cloth when visibly soiled.

•

Always replace the wiping cloth between steps (spot clean, clean, and disinfect).

•

Always use Personal Protective Equipment (PPE).

•

Adjust the bed position, siderails, headboard, and footboard as needed for ease of cleaning and 
disinfection.

Prepare the Bed for Cleaning and Disinfecting 

a.

Fully extend the foot section and powered width extensions.

b.

Unplug the bed.

c.

If it is necessary to remove the support surface, go to “Install the Surface and Air Supply Unit” 
on page 57, and do the installation steps in reverse order.

STEP 1: Cleaning

a.

As necessary, first remove visible soil from the bed and the support surface using a wiping cloth 
soaked with an approved cleaner/disinfectant (see “Table 1: Approved Cleaners/Disinfectants” 
on page 80).

•

Give special attention to seams and other areas where soil may accumulate.

•

A soft bristle brush may be used to loosen hardened soil.

•

Use as many wiping cloths as needed to remove the soil.

NOTE:

If desired, the Compella™ support surface cover may be removed and laundered to remove visible 
soil. See “Laundry Guidelines” on page 82.

It is important to remove all visible soil from all areas before continuing to remove non-visible soil.

Cleaner/Disinfectant

Recommended for 
Routine Cleaning 
and Disinfection

Recommended for 
Disinfection against 
Clostridium Difficile 
(C.Diff)

Maintain Wetness 
(Disinfection 
Contact Time)

Wex-Cide™ Germicidal 
Detergent ready-to-use

Yes

No

10 minutes

Virex® II 256

Yes

No

10 minutes

OxyCide® Daily Disinfectant 
Cleaner

Yes

Yes

3 minutes

Clorox HealthCare® Bleach 
Germicidal Cleaner ready-to-
use

No

*

Yes

5 minutes

Clorox HealthCare® Bleach 
Germicidal Wipes

No

*

Yes

3 minutes

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands