manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 61

Scale Systems

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 47 

WARNING:

Warning

—Zero the scale 

before

 a new patient is put on the bed and whenever additional equipment is 

added to the bed. Make sure to include standard linens on the bed during the zero process. Failure to do 
so could cause an inaccurate weight reading; patient injury could occur.

NOTE:

•

If the bed is equipped with the IntelliDrive® XL Transport System, you 

can not

 zero the scale or 

weigh a patient when the bed is in 

Transport Mode

 because the weigh frame will be off-

loaded by the drive wheels making contact with the floor. 

•

If you attempt to use the scale while the bed is in 

Transport Mode,

 the 

Raise 

Bed

 control indicator on the control pod will flash 5 times and you will hear a 

triple beep. To raise the bed, press and hold the 

Raise Bed 

control until its 

indicator turns off and you hear the single confirmation beep.

To Zero the Scale

1.

Press the 

Enable

 key.

2.

Make sure that the bed is in the 

Scale Reference

 position (see “Scale Reference 

Position” on page 46). When you release the brake for this position, the 

Brake Not 

Set 

alert will sound and the 

Scale Reference 

indicator will come on solid. 

3.

Press and hold the 

0/T

 control; 

Hold 

will

 

show on the display. 

4.

Release the control when 

00.0

 shows.

5.

After you release the control, the display will flash 

CALC. 

Do 

not

 touch the bed until 

the display stops flashing 

CALC

.

When 

CALC

 stops flashing, you will see 

0.0

 on the display, the 

0/T

 control indicator 

will be green, and you will hear a single beep. The zero process is complete. You can engage the 
brake at this time. 

Weigh the Patient

Before you weigh the patient, make sure of these:

•

All items on the list defined in the “Bed Setup” section are accounted for (see “Bed Setup” on 
page 43).

•

Remove drainage bags, excess linen, and equipment that has been added since the scale was 
zeroed.

•

The patient is lying still and is centered on the support surface.

•

The  bed  is 

not

 in Transport Mode.

•

The bed is in the 

Scale Reference

 position (see “Scale Reference Position” on page 46).

NOTE:

For maximum scale accuracy when you weigh the patient, the bed should be in the 

Scale Reference

 

position; however, if necessary, you can weigh the patient when the bed in not in this position.

To weigh

—press and release the 

Scale

 control. On release of the Scale control, the 

display shows the current patient weight in kilograms. At this time, you may set the 

Brake

.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands