manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 31

Safety Information

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 17 

WARNING:

Warnings 

(continued) Obey all warnings and cautions throughout the manual and also the safety 

information below to help prevent injury and/or equipment damage:

•

Warning

—Connect the power cords to hospital grade receptacles only.

•

Warning

—To avoid the risk of electrical shock, connect the bed system to a supply mains with 

protective earth.

•

Warning

—Make sure the power cords are in a location where they will not cause trip or 

strangulation hazards and in locations where they can be easily disconnected from the power 
supply.

•

Warning

—Incorrect use or handling of the power cords may cause damage to the power cords. 

If damage has occurred to either power cord or any of its components, immediately 

remove

 

the bed from service, and contact your facility-authorized maintenance person or Hill-Rom 
Technical Support. 

•

Warning

—Fluid spills on to the bed electronics could cause a hazard. If such a spill occurs, 

unplug the bed and remove it from service. When fluid spills occur outside that seen in normal 
use, immediately do as follows:

a.

Unplug the bed from its power source.

b.

Remove the patient from the bed.

c.

Clean the fluid spill from the bed system.

d.

Have maintenance examine the system completely.

e.

Do not put the bed back into service until it is completely dry, tested, and found to be safe 
to operate.

•

Warning

—If the battery backup does not operate correctly (the bed does not articulate when 

you press an articulation control), plug the bed into AC power so that you can use the bed 
controls if necessary.

•

Warning

—Do not connect the power cord to an extension cord or multiple outlet strip. There is 

a risk of overheating and fire may cause injury or damage.

•

Warning

—Whenever a bed is being cleaned or serviced, it should be unplugged from its 

power source.

•

Warning

—Use only parts and accessories from Hill-Rom. Do not modify or change the bed 

system without approval from Hill-Rom.

•

 

Warning

—The bed has no user serviceable parts. Only authorized maintenance persons 

should service the bed system.

•

Warning

—Connect only items that have been specified as part of the device or compatible 

with the device.

•

Warning

—The communication cable connection on the patient-right side of the air supply unit 

is to be used to connect to a Compella™ Bariatric Bed frame only. Connecting any other device 
could cause patient or operator injury and/or cause severe damage to the air supply unit as well 
as any other incompatible device.

•

Warning

—Report to bed authorized maintenance persons any unusual sounds, burning odors, 

or movement deviations observed in the controls, motors, or limit switch functions.

•

Warning

—Consult your local regulations to safely discard or recycle electronic equipment and 

batteries.

•

Warning

—Do not discard as unsorted municipal waste. See your local distributor for collection 

and/or recycling systems available in your country.

 

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands