manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 91

Accessories

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 77 

•

Do not use a different sized cylinder from the size specified. The cylinder could fall or interfere 
with other operations.

•

Make sure that the holder is in a safe position before you adjust the tilt of the bed or lower the 
bed.

•

If the holder does not permit the bed to pass through a doorway, adjust the holder so that it is 
at the foot of the bed or put the holder and cylinder on the bed (remember to return the holder 
to its normal location after the transport).

Telescopic IV Poles (AD165 and AD148)

WARNING:

To help prevent personal injury and/or equipment damage, follow these warnings and cautions:

•

Warning

—Do not exceed the load capacity of the IV poles; refer to the value shown on the IV 

pole. 

•

Warning

—Make sure the IV pole is installed so that it is toward the bed and not outward. 

To Use the IV Pole with Four Hooks (AD165)

1.

Insert

 

the IV pole vertically into any of the equipment sockets at either the head end or foot end of 

the bed. 

2.

To adjust the height of the pole, do these:

a.

Loosen the knob on the pole as you hold the lower section of the pole.

b.

Hold the upper section of the pole, just below the plastic sleeve.

c.

Push the sleeve upwards, and adjust the pole to applicable height.

d.

Tighten the knob.

3.

To adjust the angle of the pole, do these:

a.

Loosen the knob on the pole as you hold the lower section of the pole.

b.

Adjust the upper section of the pole to the applicable angle. Make sure that the pole is in a safe 
position.

c.

Tighten the knob.

To Use the IV Pole with Two Hooks (AD148)

1.

Insert

 

the IV pole vertically into any of the equipment sockets at either the head end or foot end of 

the bed.

2.

To adjust the height or angle of the pole, do these:

a.

Loosen the knob on the pole as you hold the upper section of the pole.

b.

As you hold the lower section of the pole, adjust the pole to the applicable height or angle. 
Make sure that the pole is in a safe position.

c.

Tighten the knob.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands