manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 109

Specifications

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 95 

Flammability Codes—United States, Canada, and Europe

All recommended support surfaces meet the applicable United States, Canadian, and European 
flammability specifications.

Electromagnetic Emissions Guidance 

CAUTION:

Caution

—This device meets all requirements for electromagnetic compatibility per IEC 60601-1-2. It is 

unlikely that the user will encounter problems with this device because of inadequate electromagnetic 
immunity. However, electromagnetic immunity is always relative, and standards are based on 
anticipated environments of use. If the user observes unusual device behavior, particularly if such 
behavior is intermittent and associated with nearby use of radio or TV transmitters, cell phones, or 
electro-surgical equipment, this could be an indication of electromagnetic-interference. If such 
behavior occurs, the user should try to move the interfering equipment further from this device.

WARNING:

Warning

—The P7800 should not be used adjacent to or stacked with other electrical equipment. If 

adjacent or stacked use is necessary, observe the P7800 and the other electrical equipment to make 
sure they operate as intended.

Make sure the P7800 operates correctly when it is used near other electronic devices. Portable and 
mobile radio frequency (RF) communications equipment can affect electrical equipment.

WARNING:

Warning

—Portable RF communications equipment (including peripherals such as antenna cables and 

external antennas) should be used no closer than 30 cm (12 inches) to any part of the P7800 including 
cables specified by the manufacturer.  Otherwise, degradation of the performance of this equipment 
could result.

Medical equipment needs special precautions in regard to electromagnetic compatibility (EMC) and 
needs to be installed and put into service according to the EMC information supplied in the tables that 
follow.

Classification according to Directive 
93/42/EEC

Class IIa

Degree of protection against ingress of water

IP20 for the air supply unit

Degree of protection against electric shock 
for Applied Parts per IEC 60601

Type BF

Degree of protection against the 

 

presence of flammable anesthetic 

 

mixtures

Not for use with flammable anesthetics

Mode of operation

Continuous 

Sound level

≤

 62 dBA, alarm signal 

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands