manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 86

Accessories

72

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

2.

Lift the oxygen tank out of the oxygen tank holder.

3.

Lift up on the oxygen tank holder, and remove it from the equipment sockets.

Patient Helper (P7802)

WARNING:

To help prevent personal injury and/or equipment 
damage, follow these warnings and cautions:

•

Warning

—Do not exceed the 227 kg (500 lb) load 

capacity of the Patient Helper arm assembly. 

•

Warning

—Correctly attach the Patient Helper arm 

assembly; otherwise, it may fall.

•

Warning

—Do not remove or install the Patient 

Helper arm assembly while it is in a position over a 
patient. 

•

For use, the Patient Helper trapeze must be locked in the center position. 

•

The complete Patient Helper weighs 21 kg (46.3 lb). Use correct lifting 
techniques and/or ask for assistance when you install or remove the Patient 
Helper. 

The Patient Helper can be used to help assist patients with mobility. It can be rotated to 
either the left or right for better access to the patient during nursing care, or for positioning an X-Ray 
machine over the patient. 

To rotate the arm

, pull the T-handle that is on the Patient Helper mount while you turn the arm 

assembly to the left or right. 

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands