manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 95

Cleaning and Disinfecting

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 81 

b.

With a new wiping cloth soaked in an approved cleaner/disinfectant, use firm pressure to wipe 
all surfaces of the bed, air supply unit, and support surface (including laundered covers). Use a 
new or clean wiping cloth as often as necessary. Make sure the following items are cleaned:

•

Siderails and under the Caregiver Control Pod

•

Headboard and footboard

•

Areas between the footboard and support surface, headboard and support surface, and 
siderails and support surface

•

Upper frame

•

Base  frame

•

Power  cord

•

Patient pendant and pendant cord

•

Accessories (See “Accessories” on page 70.)

•

Support Surface - top and bottom

•

Clean the interface connector assembly and the support surface sleeve area shown in the 
picture below. Do not disconnect the connector.

NOTE:

Clean the folds of the support surface sleeve.

c.

Examine the following for damage:

•

Top support surface cover 

•

Bottom support surface cover and attachment straps

•

Zipper  closure

d.

The damaged items should be replaced.

STEP 2: Disinfection

a.

With a new or clean wiping cloth soaked in an approved cleaner/disinfectant, use light pressure 
to wipe all exterior surfaces of the bed previously cleaned.

b.

Make sure all surfaces

 remain wet with the cleaner/disinfectant 

for the

 specified contact 

time

.

 Re-wet 

surfaces with a

 

new wiping cloth

 

as

 

necessary. See “Table 1: Approved 

Cleaners/Disinfectants” on page 80 for the contact time.

NOTE:

If bleach is used with another cleaner/disinfectant, use a new or clean cloth/wipe soaked in tap 
water to remove any disinfectant residue prior to and after the bleach application.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands