manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 45

Standard Features

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 31 

To Activate

NOTE:

If the bed has the powered drive option and is in the 

Transport Mode

, the drive wheels will be on the 

ground and you will not be able to use the neutral position. To make small lateral movements or to get 
around tight corners, raise the bed so that the drive wheels are off the floor.

When the bed is plugged into AC power, and you release the brakes, the 

Brake not Set

 alert will sound 

to let you know that the bed is in an unsafe position. To silence the alert, either unplug the bed (for 
transport) or set the brakes.

Patient Restraint and Drainage Bag Holders

Patient Restraints

WARNING:

To help prevent personal injury and/or 
equipment damage, obey these 
warnings:

•

Warning

—Make sure restraints 

are attached to the articulating 
sections of the bed at the correct 
attachment points. 

•

Warning

—Do not adjust the 

width of the bed while restraints 
are in use. 

The bed facilitates the use of ankle, 
waist/wrist, and chest restraints.

Hill-Rom makes no recommendation in regard to the use of physical restraints. Users should refer to 
legal restrictions and appropriate facility protocols before physical restraints are used.

Foot-End Pedals

Neutral

Brake (orange pedal)

Step down on the orange
brake pedal until it stops.

Move the brake or steer
pedal to the level position.

 Steer (green pedal)

Step down on the green
steer pedal until it stops. 

Head-End Pedals

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands