Hillrom Compella Instructions For Use Manual Download Page 84

Page: 84 / 116

Accessories

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

ACCESSORIES

WARNING:

Warning

—Zero the scale

before

a new patient is put on the bed and whenever additional equipment is

added to the bed. Failure to do so could cause an inaccurate weight reading; patient injury could occur.

After you install an accessory on the bed, zero the scale. See “Scale Systems” on page 43.

Part Number

Description

Accessories for North America

P2217

IV Pole

P27601

Oxygen tank holder, vertical

P7802

Patient Helper

P7803A01

Pendant

P7803A02

Pendant, with Nurse Call

P3670A01

Respiratory circuit holder

P3670A05

Pressure transducer holder

P158

a. Adapter bracket P163 must be installed for use of P158.

Infusion Support System (ISS)

P163

ISS socket adapter

P7801

Headboard

P7512

Line Managers

Accessories for International

AC959

Oxygen tank holder 150 mm

AD101

Oxygen tank holder 110 mm (D size)

AD102

Oxygen tank holder 110 mm (E size)

AC962

Pivoting 3-liter cylinder holder

AD298

Adjustable IV pole 4 hooks

AD299

One hand adjustable IV pole, 4 hooks

AC963

Syringe-driver holder

Summary of Contents for Compella





















































































































Search results

Summary of Contents for Compella

Reviews:

Brands by name

Popular brands

Hillrom Compella, Instructions For Use Manual

Search results

Summary of Contents for Compella

Reviews:

Brands by name

Popular brands