manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 57

Scale Systems

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 43 

SCALE SYSTEMS

There are two scale systems available for the bed (see the images below). Scale System 

A 

has an 

accuracy of 0.99 kg (2.2 lb) or 1% of the patient weight, whichever is greater. Scale System 

B

 has an 

accuracy of 1.0 kg. The operating range for both scale systems is 0 kg to 454 kg (0 lb to 1000 lb). The 
display and controls for the scale systems are on the flip-up caregiver control pod on the intermediate 
siderails. 

Refer to the images and page numbers shown below to determine which instructions apply to your 
scale system:

NOTE:

Everything

 on or attached to the bed will be

 included in the scale reading

. This includes items on the 

headboard, footboard, siderails, IV poles, and drainage bag/restraint holders.

S

CALE

 “A” D

ISPLAY

The scale system continuously weighs the patient; however, the weight does not continuously show on 
the display. You must press the Weigh control to view the patient’s weight. 

NOTE:

Unless you activate a scale function, the display continuously shows the head angle of the bed.

Bed Setup

WARNING:

Warning

—Zero the scale 

before

 a new patient is put on the bed. Make sure to include standard linens 

on the bed during the zero process. Failure to do so could cause an inaccurate weight reading; patient 
injury could occur.

Refer to page 43.

Refer to page 45.

Scale A

Scale B

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands