Hillrom Compella Instructions For Use Manual Download Page 105

Page: 105 / 116

Specifications

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

SPECIFICATIONS

Bed Specifications

Feature

Dimension

Overall width

Maximum (width extenders extended)

Minimum (width extenders retracted)

a. Measured from the outermost points (bumpers), excluding air supply unit and mounting bracket.

53" (135 cm)

43" (109 cm)

Overall length

Maximum (foot section extended)

Minimum (foot section retracted)

98" (249 cm)

91" (231 cm)

Sleep deck width

40" to 50" (102 cm to 127 cm)

Sleep deck length

85" to 92" (216 cm to 234 cm)

Minimum Under-bed Clearance

4.25” (10.8 cm)—(hilow in the low position)

6.75” (17.1 cm)—(hilow in the high position)

Hi-Lo

Maximum

Minimum

Transport

b. Measured from the top of the seat section outer edge to the floor.

26.8" (68 cm)

18.5" (47 cm)

17" (43 cm)

Patient weight range

113 kg to 454 kg (250 lb to 1000 lb)

Patient height range

50" to 78" (127 cm to 198 cm)

Safe Working Load (including patient,

support surface, and accessories)

500 kg (1100 lb)

Total bed weight (including the Safe

Working Load)

950 kg (2094 lb)

Total bed weight (excluding the Safe

Working Load)

380 kg (838 lb), without the IntelliDrive® XL
Transport System
450 kg (994 lb), with the IntelliDrive® XL
Transport System

Head section angle

0° to 50°

Knee section angle

0° to 30°

Tilt angle

0° to 9°

Reverse Tilt angle

0° to 9°

Caster size

6" (15 cm)

Roller bumper size

4" (10 cm)

Summary of Contents for Compella





















































































































Search results

Summary of Contents for Compella

Reviews:

Brands by name

Popular brands

Hillrom Compella, Instructions For Use Manual

Search results

Summary of Contents for Compella

Reviews:

Brands by name

Popular brands