manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 103

Troubleshooting

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 89 

P

OWERED

 W

IDTH

 E

XTENSIONS

 

WILL

 N

OT

 E

XTEND

 

OR

 R

ETRACT

NOTE:

The bed and air supply unit 

must

 be plugged into AC power for the extensions to operate.

Make sure of these:

•

The bed and the air supply unit are plugged into AC power.

•

The communication cable is connected to the bed and the air supply unit.

•

The air supply unit is turned on.

If the air supply unit is plugged in, but the bed is 
not plugged in and/or the communication cable is 
not connected, then the 

Communication Lost 

message will show to allow you to operate the 
system in Manual mode until the bed is plugged 
into AC power and the communication cable is 
connected.

If the system meets the three bulleted conditions 
above and the powered width extensions still do 
not operate, the air supply unit may have an 
internal communication board error. If so, the 

Communication Error 

message will show. 

If you have pressed the 

Enter

 button, and you need to see the error message or confirm that there is still 

an issue, turn the air supply unit off, and then turn it on. If there is still an issue, the 

Communication 

Error 

message will show. If there is an internal communication board error, the system will continue to 

operate in the Manual mode until the air supply unit can be serviced or replaced.

T

HE

 H

EAD

 

SECTION

 W

ILL

 

NOT

 R

ISE

 

OR

 

LOWER

Make sure of these:

•

The Head Up and Down controls are not locked out.

•

The bed has battery charge or is plugged into AC power.

•

The bed CPR release handle is in the fully returned position.

•

The bed width extensions are in the fully extended or fully retracted positions.

3

Side  Deflate 
Timeout

The system was 
left with its 
sides deflated 
(Manual mode 
only).

Yes, 
warning 
on the 
display.

Occurs 30 
minutes after 
Side Deflate 
completes.

Do one of these:

•

Extend Side Deflate.

•

Inflate the sides.

Priority

Condition

Indication

Visual 
Warning

Alarm 
Condition 
Delay

Resolution

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands