manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 97

Preventive Maintenance

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 83 

PREVENTIVE MAINTENANCE

WARNING:

Warning

—Only facility-authorized persons or Hill-Rom service technicians should service the 

Compella™ Bariatric Bed System. Service by unauthorized persons could cause injury and/or equipment 
damage.

The Compella™ Bariatric Bed System requires an effective maintenance program. We recommend that 
you do 

annual

 preventive maintenance (PM) for Joint Commission certification. PM not only meets 

Joint Commission requirements but can help make sure of a long, operative life for the Compella™ 
Bariatric Bed System. PM will help minimize downtime due to excessive wear. For a preventive 
maintenance schedule, refer to the 

Compella™ Bariatric Bed System Service Manual 

(178952).

For service and/or technical information other than that specified in this manual, including fuse 
replacement, circuit diagrams and isolation of mains power, refer to the 

Compella™ Bariatric Bed System 

Service Manual 

(178952).

Do annual preventive maintenance procedures to make sure the Compella™ Bariatric Bed System 
operates as originally designed. The procedures include examinations of these:

•

Overall condition

•

Siderails

•

Controls and motors

•

Battery  Backup

•

Brakes  and  casters

•

Electrical checks

•

Scale system

•

Head angle display

•

Communication system

•

Transport system

•

Transport system batteries

•

Air supply unit

•

Support surface

•

Accessories

B

ATTERIES

Refer to the 

Compella™ Bariatric Bed System Service Manual

 (178952) for battery replacement 

procedures.

Consult your local regulations to safely discard or recycle the batteries.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands