manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 96

Cleaning and Disinfecting

82

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Prepare the Bed for Use

a.

Connect the support surface retention straps at the head and foot ends of the support surface.

b.

Plug the bed into an applicable power outlet.

L

AUNDRY

 G

UIDELINES

Laundry can be used as a 

pre-cleaning

 step for the topper. launder the topper, then follow the Cleaning 

and Disinfection instructions. 

a.

Remove the topper from the support surface.

b.

Machine wash the topper according to facility protocol. The topper can be washed at a 
maximum water temperature of 90°C (194°F).

•

Use the bleach or disinfectant as instructed in the manufacturer’s instructions.

•

To determine the amount of bleach or disinfectant to use, determine the amount of water in the 
washer, and follow the manufacturer’s dilution instructions.

•

During the wash cycle, soak the topper in the disinfectant or bleach.

•

Let the topper rinse thoroughly in clean water.

c.

Either air dry the topper, or use the 

lowest

 temperature setting of the dryer to dry the topper; 

do 

not

 exceed 70°C (158°F).

d.

Follow the Cleaning and Disinfecting instructions. See “Cleaning and Disinfecting” on page 78.

For 

rental 

beds, Hill-Rom Service personnel will follow the Laundry Wash and Dry Procedure (QS02040).

C

LEAN

 

THE

 A

IR

 S

UPPLY

 U

NIT

 F

ILTERS

For correct operation of the Compella™ Therapy 
Surface, keep the filters clean. After 800 hours of 
operation, when the air supply unit is turned on, 
the 

Replace Filter

 screen shows as a reminder to 

replace the filters. To replace the filters later, press 

Remind me later

. When the air supply unit is 

turned on again, the 

Replace Filter

 screen will show.

1.

Unplug the air supply unit from its power source.

2.

At the bottom of the air supply unit, open the two filter grill covers, and remove the filters. Do 

not

 

unscrew the filter assembly from the air supply unit.

NOTE:

The 

white 

filter housing is the air intake filter. The 

black

 filter housing is the cooling fan filter.

3.

Wash the filters in mild detergent, and let them air dry.

4.

If the filters 

can not

 be cleaned, or if the filters are damaged, replace them.

5.

Set the clean or new filters in the filter housings, and close the filter grill covers.

6.

Install the 

white

 filter housing under the side with 

three

 connectors.

7.

Install the 

black

 filter housing under the side with 

six

 connectors.

8.

If you have replaced the filters, press 

Filter has 

been replaced. 

This resets the filter counter 

for another 800 hours.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands