manualshive.com logo in svg

Hill-Rom 4038110, Instruction Manual

Share
Download
Hill-Rom 4038110 Instruction Manual Download Page 12

12

1  Important information regarding safe use

55000-00011_002_01 – 1756789 – 2017-09-06

1.6

Delivery

Before installation, check the delivered components for completeness and for any 
possible transportation damage.

• To check the delivery, unpack all components and carry out visual inspection.
• The components can be identified on the basis of the order number on the 

delivery note and / or the order-specific dimension sheet.

1.6.1

 Transportation damage

Damage claims

Claims for damage cannot be accepted unless Trumpf Medical is notified without 
delay. In the event of damage during transport or missing components, please send 
Trumpf Medical a report containing the following information:

Accompanying documents

• Damage record giving details of damage or defects.
• Primary serial number of the device or system or the serial numbers of the 

damaged components,

• Order number (shown on the delivery note and/or the order-specific dimension 

sheet)

• Name and address of the customer,
• Consignee.

1.6.2

 Return address

Returns 

In the event of a return, use the original packaging if possible.
Address returns to:
TRUMPF Medizin Systeme GmbH + Co. KG
Carl-Zeiss-Straße 7–9
07318 Saalfeld
Germany

1.7

Information for users

Note that the device may only be operated by persons who have had the 
corresponding instruction.

1.7.1

 Training for use of the device

Instruction

Training must be carried out directly at the device by qualified staff of the operator or 
by an installer of the device who has been authorised by the manufacturer.

• At the end of the briefing, it must be documented that the user in question has 

understood the special operating measures necessary regarding use for the 
intended purpose.

1.7.2

 Obligation of the user to inform and to inspect

Dealing with problems

The instruction manual must be carefully read before commissioning to prevent 
possible injuries and damage to goods.

• Check the functional capability and correct condition of the device before every 

application or handover for use.

• While the device is in use, do not fail to comply with the provisions of the 

instruction manual.

• Get the information you require from the operator’s technical service or from 

Trumpf Medical in the event of specific problems that are not treated in sufficient 
detail in this instruction manual.

1.8

Purpose of the device

1.8.1

 Identification

Conformity

The manufacturer declares that this product complies with the fundamental 
requirements according to MDD Appendix I and documents this by means of the CE 
and UL marking.

Summary of Contents for 4038110





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands