Herz pelletstar CONDENSATION 10 Operating Instructions Manual Download

Page: 59 / 94

T-CONTROL

9.13

System settings

Navigation:

→

111

→

Screen:

If touching symbol:

the network configuration will be displayed.

the Remote

– settings will be displayed.

information such as software version operating system num

ber, … will be displayed.

the screensaver settings will be displayed.

messages by E-mail can be send

Display if a USB stick is plugged in (USB-symbol). Backup of USB stick create or play
(backup, software, ...) by pressing the field.

the Modbus

– settings will be displayed.

Service special

Alarm Modul (external Modul necessary

– see „user manual Alarm – Modul“)

you get to the cascade overview (see "Operating Instructions for cascade control T-
Control")

Summary of Contents for pelletstar CONDENSATION 10































































































Search results

Summary of Contents for pelletstar CONDENSATION 10

Reviews:

Related manuals for pelletstar CONDENSATION 10

Brands by name

Popular brands

Herz pelletstar CONDENSATION 10, Operating Instructions Manual

Search results

Summary of Contents for pelletstar CONDENSATION 10

Reviews:

Related manuals for pelletstar CONDENSATION 10

Brands by name

Popular brands